How to Interface GPS Module (NEO-6m) with Arduino (2023)

1. Information about GPS

What is GPS

The Global Positioning System (GPS) is a satellite-based navigation system made up of at least 24 satellites. GPS works in any weather conditions, anywhere in the world, 24 hours a day, with no subscription fees or setup charges.

How GPS works

GPS satellites circle the Earth twice a day in a precise orbit. Each satellite transmits a unique signal and orbital parameters that allow GPS devices to decode and compute the precise location of the satellite. GPS receivers use this information and trilateration to calculate a user's exact location. Essentially, the GPS receiver measures the distance to each satellite by the amount of time it takes to receive a transmitted signal. With distance measurements from a few more satellites, the receiver can determine a user's position and display it.

To calculate your 2-D position (latitude and longitude) and track movement, a GPS receiver must be locked on to the signal of at least 3 satellites. With 4 or more satellites in view, the receiver can determine your 3-D position (latitude, longitude and altitude). Generally, a GPS receiver will track 8 or more satellites, but that depends on the time of day and where you are on the earth.

Once your position has been determined, the GPS unit can calculate other information, such as:

• Speed
• Bearing
• Track
• Trip dist
• Distance to destination

What's the signal?

GPS satellites transmit at least 2 low-power radio signals. The signals travel by line of sight, meaning they will pass through clouds, glass and plastic but will not go through most solid objects, such as buildings and mountains. However, modern receivers are more sensitive and can usually track through houses.

A GPS signal contains 3 different types of information:

• Pseudorandom code is an I.D. code that identifies which satellite is transmitting information. You can see which satellites you are getting signals from on your device's satellite page.
• Ephemeris data is needed to determine a satellite's position and gives important information about the health of a satellite, current date and time.
• Almanac data tells the GPS receiver where each GPS satellite should be at any time throughout the day and shows the orbital information for that satellite and every other satellite in the system.

2. Download and install required libraries for GPS to work in Arduino IDE

• (i) SoftwareSerial library
• (ii) TinyGPS library

3. NEO-6M GPS module

The NEO-6M GPS module is shown in the figure below. It comes with an external antenna and does not come with header pins. So you will need to solder it.

Overview of NEO-6M GPS Module

• NEO-6M GPS Chip

The heart of the module is a NEO-6M GPS chip from u-blox. It can track up to 22 satellites on 50 channels and achieves the industry’s highest level of sensitivity i.e. -161 dB tracking, while consuming only 45mA supply current. The u-blox 6 positioning engine also boasts a Time-To-First-Fix (TTFF) of under 1 second. One of the best features the chip provides is Power Save Mode(PSM). It allows a reduction in system power consumption by selectively switching parts of the receiver ON and OFF. This dramatically reduces power consumption of the module to just 11mA making it suitable for power sensitive applications like GPS wristwatch. The necessary data pins of NEO-6M GPS chip are broken out to a "0.1″ pitch headers. This includes pins required for communication with a microcontroller over UART.

Note:- The module supports baud rate from 4800bps to 230400bps with default baud of 9600.

Position Fix LED Indicator

There is an LED on the NEO-6M GPS Module which indicates the status of Position Fix. It’ll blink at various rates depending on what state it’s in

• No Blinking ==> means It is searching for satellites
• Blink every 1s – means Position Fix is found

• 3.3V LDO Regulator

The operating voltage of the NEO-6M chip is from 2.7 to 3.6V. But, the module comes with MIC5205 ultra-low dropout 3V3 regulator from MICREL. The logic pins are also 5-volt tolerant, so we can easily connect it to an Arduino or any 5V logic microcontroller without using any logic level converter.

Battery & EEPROM

The module is equipped with an HK24C32 two wire serial EEPROM. It is 4KB in size and connected to the NEO-6M chip via I2C.The module also contains a rechargeable button battery which acts as a super-capacitor.

An EEPROM together with battery helps retain the battery backed RAM (BBR). The BBR contains clock data, latest position data (GNSS or bit data) and module configuration. But it is not meant for permanent data storage.

As the battery retains clock and last position, time to first fix (TTFF) significantly reduces to 1s. This allows much faster position locks.

Without the battery the GPS always cold-start so the initial GPS lock takes more time. The battery is automatically charged when power is applied and maintains data for up to two weeks without power.

Pinout

• GND is the Ground Pin and needs to be connected to GND pin on the Arduino.
• TxD (Transmitter) pin is used for serial communication.
• RxD (Receiver) pin is used for serial communication.
• VCC supplies power for the module. You can directly connect it to the 5V pin on the Arduino.

Arduino Uno

Arduino is an open-source electronics platform based on easy-to-use hardware and software. Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter message - and turn it into an output - activating a motor, turning on an LED, publishing something online. You can tell your board what to do by sending a set of instructions to the microcontroller on the board. To do so you use the Arduino programming language (based on Wiring), and the Arduino Software (IDE), based on Processing.

Pinout

Pin Description

Arduino Uno is a microcontroller board based on 8-bit ATmega328P microcontroller. Along with ATmega328P, it consists other components such as crystal oscillator, serial communication, voltage regulator, etc. to support the microcontroller. Arduino Uno has 14 digital input/output pins (out of which 6 can be used as PWM outputs), 6 analog input pins, a USB connection, A Power barrel jack, an ICSP header and a reset button.

The 14 digital input/output pins can be used as input or output pins by using pinMode(), digitalRead() and digitalWrite() functions in Arduino programming. Each pin operate at 5V and can provide or receive a maximum of 40mA current, and has an internal pull-up resistor of 20-50 KOhms which are disconnected by default. Out of these 14 pins, some pins have specific functions as listed below

• Serial Pins 0 (Rx) and 1 (Tx) ==> Rx and Tx pins are used to receive and transmit TTL serial data. They are connected with the corresponding ATmega328P USB to TTL serial chip.
• External Interrupt Pins 2 and 3 ==> These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
• PWM Pins 3, 5, 6, 9 and 11 ==> These pins provide an 8-bit PWM output by using analogWrite() function.
• SPI Pins 10 (SS), 11 (MOSI), 12 (MISO) and 13 (SCK) ==> These pins are used for SPI communication.
• In-built LED Pin 13 ==> This pin is connected with an built-in LED, when pin 13 is HIGH – LED is on and when pin 13 is LOW, its off.

There are 6 analog input pins, each of which provide 10 bits of resolution, i.e. 1024 different values. They measure from 0 to 5 volts but this limit can be increased by using AREF pin with analog Reference() function.

• Analog pin 4 (SDA) and pin 5 (SCA) also used for TWI communication using Wire library.
• AREF ==> Used to provide reference voltage for analog inputs with analogReference() function.
• Reset Pin ==>Making this pin LOW, resets the microcontroller.

4. Connection of Arduino UNO and GPS module

Connect the four pins from UBLOX to an Arduino as follows:

GPS module ==> Arduino

• GND ==> GND
• TX ==> Digital pin (D3)
• RX ==> Digital pin (D4)
• Vcc ==> 3.3 V

Here, I suggest you to use external power supply to power the GPS module because minimum power requirement for GPS module to work is 3.3 V and Arduino is not capable of providing that much voltage.

To provide voltage use prolific USB TTL.

• USB driver

One more thing I have found while working with GPS antenna comes with module is its not receiving signal inside the house so I used this antenna.

• https://linxtechnologies.com/wp/product/sh-series-gps-antenna/

For connecting this antenna, you have to use connector:

5. JHD162a LCD

• Ground ==> Ground pin of the LCD module.
• Pin2(Vcc) ==> Power to LCD module (+5V supply is given to this pin)
• Pin3(VEE) ==> Contrast adjustment pin. This is done by connecting the ends of a 10K potentimeter to +5V and ground and then connecting the slider pin to the VEE pin. The voltage at the VEE pin defines the contrast. The normal setting is between 0.4 and 0.9V.
• Pin4(RS) ==> Register select pin.The JHD162A has two registers namely command register and data register. Logic HIGH at RS pin selects data register and logic LOW at RS pin selects command register. If we make the RS pin HIGH and feed an input to the data lines (DB0 to DB7), this input will be treated as data to display on LCD screen. If we make the RS pin LOW and feed an input to the data lines, then this will be treated as a command ( a command to be written to LCD controller – like positioning cursor or clear screen or scroll).
• Pin5(R/W) ==> Read/Write modes. This pin is used for selecting between read and write modes. Logic HIGH at this pin activates read mode and logic LOW at this pin activates write mode.
• Pin6(E) ==> This pin is meant for enabling the LCD module. A HIGH to LOW signal at this pin will enable the module.
• Pin7(DB0) to Pin14(DB7) ==> These are data pins. The commands and data are fed to the LCD module though these pins.
• Pin15(LED+) ==> Anode of the back light LED. When operated on 5V, a 560 ohm resistor should be connected in series to this pin. In arduino based projects the back light LED can be powered from the 3.3V source on the arduino board.
• Pin16(LED-) ==> Cathode of the back light LED.

6. Connection of Arduino UNO and JHD162a LCD

LCD==> Arduino

• VSS ==> GND
• VCC ==> 5V
• VEE ==> 10K Resistor
• RS ==> A0 (Analog pin)
• R/W ==> GND
• E ==> A1
• D4 ==> A2
• D5 ==> A3
• D6 ==> A4
• D7 ==> A5
• LED+ ==> VCC
• LED- ==> GND

Programming

Arduino IDE

#include <LiquidCrystal.h> #include <SoftwareSerial.h> #include <TinyGPS.h> float lat = 28.5458,lon = 77.1703; // create variable for latitude and longitude object SoftwareSerial gpsSerial(3,4);//rx,tx LiquidCrystal lcd(A0,A1,A2,A3,A4,A5); TinyGPS gps; // create gps object void setup(){ Serial.begin(9600); // connect serial //Serial.println("The GPS Received Signal:"); gpsSerial.begin(9600); // connect gps sensor lcd.begin(16,2); } void loop(){  while(gpsSerial.available()){ // check for gps data  if(gps.encode(gpsSerial.read()))// encode gps data  {  gps.f_get_position(&lat,&lon); // get latitude and longitude  // display position  lcd.clear();  lcd.setCursor(1,0);  lcd.print("GPS Signal");  //Serial.print("Position: ");  //Serial.print("Latitude:");  //Serial.print(lat,6);  //Serial.print(";");  //Serial.print("Longitude:");  //Serial.println(lon,6);  lcd.setCursor(1,0);  lcd.print("LAT:");  lcd.setCursor(5,0);  lcd.print(lat);  //Serial.print(lat);  //Serial.print(" ");  lcd.setCursor(0,1);  lcd.print(",LON:");  lcd.setCursor(5,1);  lcd.print(lon);  } } String latitude = String(lat,6);  String longitude = String(lon,6); Serial.println(latitude+";"+longitude); delay(1000); } 

7. Result

Video